登录

  • 登录
  • 忘记密码?点击找回

注册

  • 获取手机验证码 60
  • 注册

找回密码

  • 获取手机验证码60
  • 找回
毕业论文网 > 毕业论文 > 理工学类 > 工程力学 > 正文

简支梁桥设计—B毕业论文

 2021-07-13 12:07  

摘 要

本毕业设计为简支梁桥设计,设计跨径为18米,桥面净宽为净7.0附2×0.5米人行道,设计荷载为公路-Ⅱ级。

本毕业设计包括桥跨设计、支座设计、桥墩设计和基础设计。桥跨设计主要包含主梁设计(主梁采用I型截面),横隔梁设计和桥面板设计。在桥跨设计过程中首先拟定各部分的结构尺寸,然后对其进行内力计算,最后再进行配筋计算。在主梁设计过程中还需要对其进行裂缝验算和预拱度设计。支座采用板式橡胶支座,拟定支座尺寸并对支座进行偏转验算和抗滑验算。桥墩墩身高10米,采用重力式桥墩,桥墩结构设计包括墩帽和墩身结构设计,墩身采用砌体结构,对墩身截面进行偏心距验算和强度验算。基础采用刚性基础(地基土为碎石土),根据承载力计算确定其尺寸,进行了基础结构设计,然后对基础进行沉降验算和稳定性验算。

关键词:结构设计,内力计算,验算,配筋

Abstract

The graduation design project is simply supported beam bridge design span of 18 meters, bridge deck width for net 7.0 attached 2 x 0.5 meter sidewalk design load for highway – II level.

The design of this graduation design project includes bridge span design, bearing design, bridge pier design and foundation design. Bridge span design mainly contained the the main beam design (main beam using the I section), horizontal beam bridge design and panel design. In the bridge design process, the first part of the structure decide size of the structure, and then the internal force calculation, and finally in the reinforcement calculation. In the main beam design process also need to checking crack and design.amber. The bearing is made of plate type rubber bearing, and the size of the bearing is drawn up and the deflection of the bearing is checked. the height of pier is 10 meters by gravity piers, pier structural design including pier caps and pier body structure design, The construction of pier body cross-section use masonry structure, pier body section need eccentricity checking and checking the strength. Foundation utilize rigid base (soil main contain gravel soil), according to the capacity calculation to determine its size, infrastructure design was then carried out on the basis of the settlement checking and checking stability.

Key Words:structural design, internal force calculation ,checking calculation,reinforcement

目 录

第1章 桥跨设计 1

1.1 桥跨结构设计 1

1.2 主梁计算 2

1.2.1主梁恒载内力计算 2

1.2.2 主梁活载内力计算 3

1.2.3主梁内力组合 14

1.2.4主梁配筋计算 17

1.2.5 裂缝验算 25

1.2.6 挠度、预拱度计算 25

1.3 横隔梁设计 27

1.3.1横隔梁截面内力计算 27

1.3.2 横隔梁配筋计算 31

1.4 桥面板设计 34

1.4.1 桥面板内力计算 34

1.4.2 桥面板配筋计算 36

第2章 支座、桥墩和基础设计 39

2.1 支座设计 39

2.1.1支座选型与结构设计 39

2.1.2 支座验算 40

2.2 桥墩设计 41

2.2.1 桥墩结构设计 41

2.2.2 桥墩验算 43

2.3 基础设计 50

2.3.1 基础选型 50

2.3.2 确定基础埋深 50

2.3.3 按持力层地基承载力确定基底尺寸 50

2.3.4 基础沉降计算 52

2.3.5 基础稳定性验算 54

参考文献 56

附 录 57

致 谢 58

第1章 桥跨设计

1.1 桥跨结构设计

桥跨纵横断面布置及各构件大样图见附件。

(1)设计参数:

桥面净宽:净7.0附2×0.5米人行道

跨径:标准跨径Lo=18m

可变荷载:汽车荷载,公路-Ⅱ级,人群荷载取3.0KN/m

(2)主梁结构设计[1][2]

主梁截面采用I型截面,主梁标准跨径为18m,计算跨径17.6m,横断面由7片预制I梁组成,主梁总长为17.96m。I梁主梁全高为80cm,上、下翼缘全宽为30cm,腹板厚度为16cm,腹板宽度为40cm。主梁材料:采用C40混凝土(重度为),主筋采用HRB400 ,其他采用HPB300。主梁结构图见附件。

(3)横隔梁结构设计:

横隔梁高度为60cm,横隔梁为了施工方便,横隔梁上、下肋宽分别为16cm、14cm。采用C25混凝土现浇,钢筋采用HPB300。横隔梁结构图见附件。

(4)桥面板结构设计:

桥面板采用现浇整体桥面板,桥面板厚度为25cm,桥面板宽度为9.0m,长度为17.96m。桥面板材料:采用C40混凝土(重度为),主筋采用HRB400 ,其他采用HPB300。

(5)桥面铺装设计[1][2]

您需要先支付 80元 才能查看全部内容!立即支付

企业微信

Copyright © 2010-2022 毕业论文网 站点地图