登录

  • 登录
  • 忘记密码?点击找回

注册

  • 获取手机验证码 60
  • 注册

找回密码

  • 获取手机验证码60
  • 找回
毕业论文网 > 毕业论文 > 机械机电类 > 测控技术与仪器 > 正文

配电间的温湿度检测系统设计毕业论文

 2022-06-06 10:06  

论文总字数:19621字

摘 要

配电间与监控室通常是连接在一起的,在同一个建筑物中。在夏天的时候,室内的温度往往能够达到50℃以上。在这个时候,变压器的温度就会比室温还要高,配电设备长时间超负荷工作,并且在配电设备内部的元器件可能会线路老化,配电间可能会发生火灾或者爆炸。配电间温湿度监测的时候,配电间的湿度过大的话就十分容易造成电弧短路事故。如果不保证配电间的湿度在一个安全范围的话,将会对社会造成很严重的损失。

本系统运用STM32控制器,通过温湿度传感器采集数据,并且将数据送给AD转化器,把模拟量转化为数字量。此时把数字量传输给STM32进行处理,同时将测得的温湿度显示在液晶屏上。通过无线蓝牙模块把温湿度传送给监控室,若检测值比配电间允许的最大温度、

湿度值大,则蜂鸣器发出报警。

关键词:温湿度 传感器 控制器 无线传输

Distribution room temperature and humidity detection system design

Abstract

Distribution room and control room is usually connected together, in the same building. During the summer, the indoor temperature can reach more than 50 degrees Celsius. At this time, the temperature of the transformer will be better than the room temperature is high, the power distribution equipment overload for a long time, and within the distribution equipment components may be aging line, distribution room fire or explosion may occur. Distribution room temperature and humidity monitoring, distribution room if the humidity is very easy to cause arc of short circuit accident. If we do not guarantee the distribution room humidity in a safe range, will cause serious damage to the society.

This system uses STM32 controller, through the temperature and humidity sensors to collect data, and send the data to the AD converter, the analog into digital quantity. At this point the digital transmission to the STM32 for processing, and at the same time will measure temperature and humidity display on the LCD screen. Through wireless bluetooth module sends the temperature and humidity to PC, after compared with the preset value, does not conform to the buzzer sounded the alarm.

Key Words:Temperature and humidity; The sensor ;The controller ;Wireless transmission

目录

摘 要 II

Abstract III

第一章 绪 论 1

1.1课题的研究背景 1

1.2本课题的研究意义 1

1.3温湿度传感器国内外研究现状 1

1.4温湿度传感器技术的发展趋势 2

第二章 温湿度监测系统的总体设计方案 4

2.1 系统设计的工作流程 4

2.2 系统整体功能 4

2.3 主要元器件的选择 5

2.3.1温湿度传感器的选择 5

2.3.2 温湿度传感器HMT100 6

2.3.3 控制器的选择 8

第三章 系统硬件电路设计 9

3.1 控制器概述 9

3.1.1 ARM处理器简介 9

3.1.2 STM32F107VC简介 9

3.1.3 JTAG下载模块 10

3.2 电源电路 11

3.4 A/D转化模块 12

3.4.1 A/D7705简介 12

3.4.2 AD7705与STM32的接口电路 13

3.5 LCD显示模块 14

3.5.1 TFT—LCD简介 14

3.5.2 TFT—LCD的特点及管脚说明 14

3.6 报警模块 15

3.7 蓝牙传输模块 16

3.7.1 蓝牙简介 16

3.7.2 ATK-HC05-V11蓝牙串口模块 16

第四章 系统软件设计 18

4.1 开发环境介绍 18

4.2 AD7705数据采集模块软件设计 19

4.3 液晶显示模块软件设计 22

4.4 蓝牙传输模块 23

第五章 系统调试 26

5.1 系统调试方案 26

5.2 系统调试与结果 26

5.3 调试过程中的问题和改进 26

第六章 结语 28

参考文献 29

致 谢 30

第一章 绪 论

1.1课题的研究背景

在科技水平飞速发展的今天,出现了越来越多的高性能设备,在许多的行业里对温度、湿度的要求越来越高。在过去对于温湿度的检测主要是依靠人力,让工作人员轮流的值班,不断的巡查等方式来测量和记录环境中的温湿度数据。在过去的这种方式下,不仅效率很低,不利于人才资源的充分利用,而且缺乏科学性,许多重大事故都是由于人的一时疏忽造成的。对于人才资源的浪费,管理不及时等问题,温湿度监控系统就可以很好的解决,这是由于它的智能化设计所决定的。

1.2本课题的研究意义

在天气炎热的时候,设备工作的时候产生热量使得室内的温度升高,由于室内温度过高就有可能影响配电设备的正常使用,再加上配电设备长时间超负荷工作,线路老化和没有能够及时维修,这些问题都可能带来严重的危害。与此同时在查阅有关的资料之后,我们得知湿度过大的时候设备可能会产生电弧短路。如果不预防的话,造成的损失也会十分惨重。为了预防这样的情况我们就要在配电间当中安装一个温湿度的检测系统,对配电间的温湿度进行实时的监测,当传感器测到的数据超过配电间允许的最大值得时候,系统就发出报警,提醒工作人员对配电间进行查看,做到及时发现及时处理[1][2][3]

请支付后下载全文,论文总字数:19621字

您需要先支付 80元 才能查看全部内容!立即支付

企业微信

Copyright © 2010-2022 毕业论文网 站点地图