登录

  • 登录
  • 忘记密码?点击找回

注册

  • 获取手机验证码 60
  • 注册

找回密码

  • 获取手机验证码60
  • 找回
毕业论文网 > 毕业论文 > 环境科学与工程类 > 环境科学 > 正文

武穴市某医院水处理系统扩容设计毕业论文

 2021-11-07 08:11  

摘 要

为对抗新型冠状病毒疫情,武汉市某医院临时将原有的100张床位的内科住院部扩建为总计350张病床的传染病区住院部,因此,本设计要求为该医院传染病区住院部排放的医疗污废水设计配套污水处理设施。设计水量为350×800=280000L/d=280t/d。医疗废水通常是指从医院各个部门的各个科室房间产生排放的污水,由于废水源头杂乱,医疗废水的成分也十分复杂,除各种化学药剂,还还有大量病原细菌和病毒,尤其本次新冠疫情中新冠病毒的传染性极高,使其污染具有空间性、传染性和潜伏性。

本次设计着重考虑具有传染性的细菌和病毒,尤其将本次疫情中的2019-nCoV病毒列入考虑范围。根据多方面因素,采用生物接触氧化法 二氧化氯消毒工艺,工艺流程大致概括为:污水先于预接触消毒池中第一次加药进行消毒,然后在化粪池分解部分有机固体污染物,随后在格栅井去除较大的固体污染物,在调节池进行均质均量的处理后,污水流入生化池并在其中去除大部分有机污染物,最后沉淀池泥水分离后上清液进入消毒池中,消毒后达标排放。污泥部分进入污泥浓缩池,经过重力浓缩后外运进行妥善处理。

该设计不需要大规模改动医院原有污水处理设施,工艺流程简单,操作方便,占地小,效率高。

关键词:医疗废水;污水处理;消毒方法

Expansion Design of Sewage Treatment System in Wuhan

Student majoring in environmental science LinWeiyi

Tutor LiuJingxuan

(Wuhan University of Technology,Wuhan 430070,China)

Abstract

In order to against the outbreak of Novel Coronavirus Pneumonia, a hospital in Wuhan city temporarily expanded the original internal medicine inpatient department with 100 beds into the inpatient department of infectious disease wards with a total of 350 beds. Therefore , this project requires the design of supporting sewage treatment facilities for the medical sewage discharged by the inpatient department of the infectious disease wards of the hospital.The designed water volume is 350×800=280000L/d=280t/d. Medical waste-water usually refers to the sewage discharged from the room of each department of the hospital. Because of the confusion of waste-water sources, the composition of the medical waste-water is also very complex, containing a large number of pathogenic bacteria, viruses and chemical agents.In particular, novel corona-virus is highly infectious in this covid-19 outbreak, making its pollution more spatial, infectious and latent.

The design should focus on the presence of infectious bacteria and viruses, especially the pollution of pathogenic microorganisms such as the 2019-nCoV virus. According to each factor, the disinfection process of biological contact oxidation chlorine dioxide was adopted. y, process generally summed up as: sewage after preliminary contact disinfection pool do first dosing disinfection treatment, for the first time, and then in the septic tank part decomposition organic solid contaminants, enter the grille to remove large suspended solids in regulating pool to homogeneous average of sewage, into the biological contact oxidation pool to remove most of the organic pollutants, spate separation in the sedimentation tank, finally enter the pool disinfection disinfection discharging standard. The remaining sludge goes into the sludge concentration tank, after gravity concentration, it is dehydrated and transported abroad for proper treatment.

The design does not need to change the hospital's original sewage treatment facilities, the process is simple, easy to operate, small footprint, high efficiency.

Key words: medical waste-water; Sewage treatment; Disinfection method

目录

1. 绪论 1

1.1. 设计背景 1

1.2. 工程总论 1

1.3. 设计原则 1

1.4. 设计内容 1

2. 工程总体设计 2

2.1. 工程规模 2

2.1.1. 污水量 2

2.1.2. 工程规模 2

2.2. 污水水质及处理程度 2

2.2.1. 设计进水水质 2

2.2.2. 设计出水水质 3

2.2.3. 处理程度 3

3. 污水处理工艺选择 4

3.1. 处理工艺选择原则 4

3.2. 处理工艺的技术可行性分析 4

3.3. 污水处理工艺选择 4

3.3.1. 工艺流程 4

3.3.2. 物理处理工艺 5

3.3.3. 化学处理工艺 5

3.3.4. 生物处理工艺 5

3.4. 消毒工艺选择 9

4. 污泥处理工艺选择 12

5. 工艺流程 13

6. 构筑物设计计算 14

6.1. 预接触消毒池 14

6.1.1. 设计依据 14

6.1.2. 设计说明 14

6.1.3. 设计计算 14

6.2. 化粪池 16

6.2.1. 设计依据 16

6.2.2. 设计说明 16

6.2.3. 设计计算 16

6.3. 格栅 17

6.3.1. 设计依据 17

6.3.2. 设计说明 17

6.3.3. 设计计算 17

6.4. 调节池 19

6.4.1. 设计依据 19

6.4.2. 设计说明 19

6.4.3. 设计计算 19

6.5. 生物接触氧化池 20

6.5.1. 设计依据 20

6.5.1. 设计说明 21

6.5.2. 设计计算 21

6.6. 沉淀池 23

6.6.1. 设计依据 23

6.6.2. 设计说明 24

6.6.3. 设计计算 24

6.7. 接触消毒池 26

6.7.1. 设计依据 26

6.7.2. 设计说明 26

6.7.3. 设计计算 26

6.8. 快滤池的设计 28

6.8.1. 设计说明 28

6.8.2. 设计计算 28

6.9. 污泥浓缩池 29

6.9.1. 设计依据 29

6.9.2. 设计说明 29

6.9.3. 设计计算 29

6.10. 污泥脱水系统 32

6.10.1. 设计依据 32

6.10.2. 设计说明 32

6.11. 二氧化氯发生器 32

7. 废水处理站总体布置 33

7.1. 布置原则 33

7.2. 高程确定 33

7.3. 站内建设 34

7.3.1. 辅助构筑物 34

7.3.2. 绿化 34

7.3.3. 采暖与通风 34

7.3.4. 消防与安全 34

8. 人员防疫 36

9. 环境保护 37

9.1. 环境保护范围 37

9.2. 污染源及污染物 37

参考文献 39

致谢 41

绪论

设计背景

医疗废水主要是指从医院各个部门的各个科室房间产生排入污水处理系统的污水,复杂的产生源头决定了医院污水的组成成分也十分复杂,其中含有大量的病原微生物以及对环境有毒害作用的物理或化学污染物、放射性污染物等。这一类污水的污染具有空间性、急性传染性和传染潜伏性三种特殊性质。医院污水如果没有经过妥善处理就直接排放,将会对环境造成巨大危害,其影响与危害甚至比工业废水更加具有严重性,是危害人体健康安全的一个重要源头。本设计的要求是设计一套对病原微生物拥有良好后续处理能力,出水水质达到相应污水排放标准并且能够稳定运行的医疗污水处理设施。此外,由于需要依托医院现有医疗废水处理系统改扩建,场地方面的限制较大,设备的占地面积以及排布也应列入考虑。值得注意的是,由于考虑到新冠病毒有形成高浓度气溶胶散布的可能性,处理设施设备要求封闭性,并兼顾后续维护、投药、消毒清理的便捷性。

工程总论

工程名称:医院污水处理涉及建设项目

建设规模:污水处理量为280t/d

设计原则

该设计将根据我国环境保护相关法律法规、工程建设项目有关规定要求,遵循以下原则:

您需要先支付 80元 才能查看全部内容!立即支付

企业微信

Copyright © 2010-2022 毕业论文网 站点地图